Wireless RGB & DMX Controllers
RGB Smart WiFi Controller, 12A
£70.00
-
Have you ever wanted to control your LED lights with your phone? This little gem will let you do just that. The RGB Controller uses a Wifi connection through an IOS or Android Smartphone.
You can use this to control RGB leds, single colour leds, Colour temperature leds, and RGB bulbs.
You'll need to download an app to your phone, but once done, there are few limitations to the effects you can program in.
App for Iphone
App for Android
Works wonderfully with our 12v/24v RGB modules and strips.
- Communication Standard: 2.5GHz Wi-Fi, 802, 11b/g/n Protocol
Operating Voltage : 12v-24v
Output Current: Max 12A - 4Ax3ch
Max Output Power: 144w/288w (12v/24v)
Output Control: Single Colour, CT, RGB LEDs
Range: up to 50m indoor and 100m outdoor
RGB CHange Mode: 32 Fixed Modes, 8 DIY Modes
Scene Mode: RGB 9 Modes, CT 3 Modes
Operating Temp: -30*C ~ 55*C
Dimensions: 128 x 73 x 45mm + aerial
Weight: 320g
Software installation required: Instruction manual supplied
Wireless Receiver
£66.00
-
The LED Receiver gets information wirelessly via the 3050 wireless transmitter using a 300Hz~20KHz PWM pulse signal.
*This receiver needs to be used with our transmitter LT-3050.
When the 2 are set to the same frequency the receiver will repeat the signal sent from this transmitter. Multiple receivers can be used with the same transmitter.
A sending end can configure unlimited receiving ends.
A very good solution for the LED project that needs to sync control wirelessly i.e, between buildings, both sides of the roads, river banks and bridges, etc.etc.
Can be used with single colour and RGB strips/modules.
- Operating Voltage : 5v~24v
Max Current Load: 5A x 3ch MAX 15A
Max Output: 75w/180w/360w (5v/12v/24v)
Working Frequency Channel: 2.4GHz ISM 64 channels
Receiver Sensitvity: -96dBm
Range: Up to 350m
Dimensions: 175 x 44 x 30mm + aerial - Datasheet Download
DMX Wireless Transceiver
£66.00
-
LT-870 Wireless DMX512 transceiver transfers the standard DMX512 protocol data by wireless transmission. One send, one receive or multiple receive. (Supporting point to point, point to multi-point), a sending end can configure multiple receiving ends as long as the receiving end and sending end are set as same frequency point.
This product can act as the transmitter and receiver. See the download sheet for the settings. It can also be used with our LT-874-5A receiver decoder with OLED display.The product is used for DMX console and lamp. The wireless data transmission between lamps replaces cable transmission which relies on twisted-pair, etc., for a long time. No delay and data is real-time and reliable during data transmission process.
-
Input Voltage : 5v~24v
Working Frequency Channel: 2.4GHz ISM 64 channels
Transmitted Power: -96dBm
Range: Up to a max. 350m
Working Temperature: -20*C-55*C
Dimensions: 175—44—30mm + aerial
The product adopts 2.4GHZ RF global open ISM frequency channel, which is a low-cost, powerful wireless DMX512 transceiver and widely applied to DMX512 controllers from various manufacturers.
64 channels choices, users can use 64 groups wireless network independently without interference in one place.
Use relay Settings if need further increase the communication distance.
- Datasheet Download
DMX Wireless Decoder with OLED Display
£74.00
-
This 4chx5A constant voltage DMX driver with OLED display receives standard DMX512 protocol data wirelessly.
4 choices of power level.
Visual communication distance can reach 350 meters at maximum transmitted power.
Self-test inspection mode for testing the wireless link quality during installation.
You can use relay settings or connect to a Booster Antennae to further increase the communication distance.
Designed to work with our LT-870 transceiver.
- Operating Voltage : 5v (100w), 12v (240w) or 24v (480w)
Working Frequency Channel: 2.4GHz ISM 64 channels
Transmitted Power: -96dBm
Range: Up to a max. 350m
Working Temperature: -20*C-55*C
Dimensions: 175 x 53 x 30mm + aerial
Output Current: Max 20A - 5Ax4ch - Datasheet Download
Wireless Transmitter
£70.00
-
The LED Transmitter sends information wirelessly using a 300Hz~20KHz PWM pulse signal.
*This transmitter needs to be used with our receiver LT-3053-5A.
When the 2 are set to the same frequency the receiver will repeat the signal sent from this transmitter. Multiple receivers can be used with the same transmitter.
A sending end can configure unlimited receiving ends.
64 channels choices; users can use 64 groups of wireless network independently, without interference, in one place
A very good solution for the LED project that needs to sync control wirelessly i.e, between buildings, both sides of the roads, river banks and bridges, etc.
Can be used with single colour and RGB strips/modules.
- Operating Voltage : 12v (240w) or 24v (480w)
Working Frequency Channel: 2.4GHz ISM 64 channels
Transmitted Power: 20dBm
Range: Up to a max. 350m
Dimensions: 175 x 44 x 30mm + aerial
Output Current: Max 20A - 5Ax4ch - Datasheet Download